Visual edgebanding in 3D Model
Hi all, recent new user here after 25 years using "other' software, can't work out how to visually display the banded edges of a component so I can quickly verify which edges need banding added. We do a lot of large commercial/hospital type projects andFace 6 Edge Trim Start Location
I am looking for a method to change where the face 6 edge trim geometry starts. Currently it sets the Y start point .125" off the sheet. Due to one of our machines limits, it is necessary to set this to Y=0. Has anyone else had to make this change & foundWhere can I adjust the reveal between drawer fronts in a drawer stack?
Usually in Product Prompt>Face Option setting the reveals here is all I need. But today I was dimensioning out a drawer stack and realized MV just decided only one reveal (between lowest two drawers) should be 5/32. Our shop standard is 3/32. Where canSequential Numbering & Labels from Single Product
Is there a way to use a single product and enter a range or set of numbers (0-100 or 123, 456, 789, etc.) and have an identical product processed with multiple labels for each number? Each item would be a duplicate, but having the labeling this way wouldFEATURE REQUEST: hardware List
https://community.microvellum.com/portal/en/community/topic/hardware-list-preview Much like you can use Parts List Review (MVREVIEWPARTSLIST) to see parts and materials assigned to products, I would like to view a list of hardware assigned to productsNesting Position Preview & Machine Origin Arrow on Part Label
Hi everyone, I'd like to suggest a practical improvement to part labels that would help operators quickly identify parts on the nest sheet without extra steps. Current situation: Our labels already show a small furniture preview image (see photo). ThisParts Nesting Position on the label
Hi everyone, I have a question regarding part labels in Microvellum. Is it possible to display the part’s nesting position (ID/number) directly on the label (sticker)? For example, so the operator can easily identify the part’s location in the nest sheet.Simple (I hope) Question - Toe Kick Return
Where would I go to create a toe kick return to the back wall?Innergy design
I saw this on Innergy’s website. Does anyone know more about it? I was wondering if it would be similar to Microvellum. Design - INNERGYCreating Custom Pocket Machining - Hatch Polyline
Quoting from the knowledge base, "Hatch Polyline Allows you to create a pocket routing operation for a custom shaped polyline" I must have a curse with commands not working right unless I try ten thousand times because I am having trouble replicatingOne Upper With Four Doors?
This may be a silly question but I'm making uppers for a laundry room, 4 doors across. I originally had a one door left swing, a two door with handles in the middle and then a one door right swing. But my boss said it would be better to make it all oneParametrics Trail
Currently a huge struggle for our teams is: When making any kind of changes to a cabinet, often times the change doesn't take effect OR the change comes out different than we expected. We are pretty sure this is usually due to that specific variable beingHave no BSB 2025 or 2026 activations.
OK.... I downloaded BSB 2026. Couldn't register it, received an email from support to delete a few files so the 'activate license'' pop up would show. I enter my ID & password and I get activation failed. No remaining activations. So forget 2026 and goWall Association Prompt?
I was wondering if anyone knows of a way to look up, at the product level, if a product is associated to a wall and reference that data in a formula?Revert Cell In Product Prompts to Default
Would it be possible to add an option when in Product Prompt or Subassembly Prompts where you right click on a cell and there is a "Revert to Default Value" option that puts the cell back to the default value or formula for the spec group? Maybe it'sFormula Reset in Prompts
Is there a way to have a text field prompt reset back to a formula? For example if I have a formula set to X=M!Upper_Door_Thickness and visible as a text field, but allow the user to override this value when a checkbox is checked, then when the checkboxAuto Unit Conversion In Microvellum/Innergy Design
In Microvellum & Innergy Design it would be nice to be able to use any unit type in any entry box and have it automatically convert it to the current unit, so if you are in Inches but you had a metric measurement for a feature you could input 127mm andAdding Custom Door Profile
We typically run our profiled cabinet doors through a shaper/moulder/raised panel cutter. The only info i can find adding a custom profile for cab doors is through the MDF profile doors. Having to map out routers is insane, there has to be somewhere whereHnager Notch when there is a filler
When I have a row of upper cabinets, the hanger notch is fine. But when I add a filler in the prompts and change the filler height, the hanger notch also changes. I can fix it in the part properties, but I don’t want to have to check that every time IAdding Flip Up Door to Top of Cabinet
Hi What is the best way to add Flip up door to top of cabinet? I was thinking adding Component Insert then start rotation and adjusting to top position Can you please share better idea ? I appreciate your contribution Thank youRouter Simulation
Trying to find the router simulation so we can see what will happen before sending to the CNC. Is this hidden somewhere?Report Designer Blank
I'm trying to work in report designer but when I open a report and select a work order the page is blank. I've tried different reports and different work orders, but none of them show anything. The one image I've attached shows the report I get when IChanging Current Configuration
I think it would be nice if there was the option to change the current configuration without exiting and relogging in. It would be nice if maybe you could do it from the tool bar also.MV Undo Command
I feel like it would be extremely useful to have a MV Undo command, Maybe there are some major technical hurdles here but it seems like one of the biggest improvements to useability as a new adopter... Adding this from the comments below for better visibility.Foundation Library Product Highlight: The Master Extruded Countertop
With Foundation Library build 24.0520, extruded products are continuing an overhaul to their functionality. Four existing extruded countertop products within the Extruded Products category have been replaced with updated versions based on a new masterProducts not placing on walls properly in Bricscad
Is this happening to anyone else? I am placing products on walls like I have been for 6 years and its just not working the same anymore. Problem: When I right click on placing a product, I anchor either left/right/center as I have in the past. I pickFEATURE REQUEST: Name Entry for Analyzed Products
Adding a field to the "Save Analyzed Product" UI that would allow the user to provide the name of the product would definitely improve the user experience and eliminate the added steps of renaming through the Product Viewer or Product List (Overdrive35mm Drill in Tool holder
We have always had out 35mm drill for boring hinge hole in a tool holder. Since we have been using MV I can not figure out how to tell it what tool to pick for that operation. Can someone point us in the right direction.Toolbox BSB: The Successor to Toolbox OEM
Hi Microvellum Community! Today, we’re announcing that maintenance for Toolbox OEM will officially conclude on July 20, 2025, as we transition to a new bundled CAD foundation powered by BricsCAD. This planned change coincides with the launch of ToolboxNew Product Prompts
Is there a reason why we can't have the same 4 buttons for the Product Prompts that we have for Edit Design Data? I shouldn't have to check or uncheck when i want to redraw the product.Hinge Info on Part Labels
Since I'm quite terrible at customizing reports beyond rearranging and sizing, can someone tell me how to add a line on the Part Labels giving the specific hinge used for that particular door? ThanksSystem 32 Subassembly Prompt
has anyone come across the "System_32" prompt in a subassembly and know what its for?Have you taken the IIBT Survey Yet?
You’ve probably seen us mention the INNERGY Industry Benchmarking Tool (IIBT) already, but I figured I’d bring it up here since there’s only about 30 days left before the survey closes. If you’ve ever wondered whether your margins are actually good, or5 Drawer Bank
I found a Base 3 Drawer Split Top Drawer but I was wondering if there's a "Base 3 Drawer Split Bottom Drawers" product. I'm looking to have the top drawer full width with two rows of split drawers below. How would you go about this?Double Click For Sectioning Elevation To Set Distance
When using the section command for a 2D Wall Elevation, it prompts you for the distance to make the section (Defaults to center). I want the double click measure option like product prompts to select the distance. I want this so i can pick the point whereMicrovellum Portal - Software Management Access (Unavailable?)
We’ve had reports that the Software Management section in the Microvellum Portal isn’t accessible for some users. We’ve looked into it, and it doesn’t appear to be widespread. If you’re running into this issue, send an email to [email protected],Attn: Ratko Tubic - Tab Pull Back Rabbet Toggle
@Ratko Tubic - You posted/commented on the last / yesterday MV webinar about OPTION for the BACK RABBET on Tab Pulls - (and also the BACK DRILLING as well) - We did this already here. We / I added a Global Toggle Option to TURN the back RABBETFoundation Reports - Why so slow?
Ok question ... Why are Foundation Library Reports SOOOO SLOOOOW For instance ... Work Order Summary - This dialog box below must flash like a dozen times! Obvious it's re-querying something all those times ... but why? (Happens with Nest OptimizationFormula Editor AI Assistant + Syntax Highlighting Preview
Did you miss our release review event today? If so, then you missed our preview of the new AI Assistant and Syntax Highlighting for the Formula Editor. The AI Assistant helps you create, edit, and troubleshoot formulas, while syntax highlighting makesHardware not appearing in subassemblies.
Hi team. Feel like I'm banging my head up against the wall here and have generally found support/help for Microvellum Bricscad to be pretty bloody poor. So, any help is appreciated. There are so many more hardware parts I can see, preloaded in the libraryNext Page
INNERGY Industry Benchmarking Tool
MVU eLearning
Grow Your Knowledge
Follow along with RJ as he takes you on a journey to build your foundational knowledge of Toolbox.
Announcements
New Microvellum Release Available Now: Build 26.1.0520.641
We are happy to announce that Microvellum build 26.1.0520.641 is now available! This build includes resolutions for issues with room names, the find and replace feature within Workbook Designer, item number scaling, and more. A new option has been addedWe've Upgraded Your Microvellum Experience
We’re making it easier for you to get more out of Microvellum! As Microvellum continues to evolve, we’re taking a deliberate step to simplify how the platform is delivered while providing more value to our users. The result is a more streamlined approachNew Microvellum Release Available Today: Build 26.1.0422.641
We are happy to announce that Microvellum build 26.1.0422.641 is now available! This build includes resolutions for issues with product dimensioning, associative machining, grid view within the processing center, sawing reports, and more. A new optimizationNEXT UP: Customer Focus Group and May Feature Release Events
We have two upcoming product events coming up, and we’d love to have you join us live. Q3 Customer Focus Group - May 19 at 1:30 PM PST - time zone calculator This is your chance to share feedback and help influence what we’re working on next. - RegisterNew Foundation Library Release Available Today: Build 26.0430
We are happy to announce that a new update for the Foundation Library, Build 26.0430 is now available! New releases of Microvellum's Foundation Library include resolutions for numerous issues, numerous enhancements to existing products and variables,
Follow us on: