Hardware array
I've attached a screenshot of a hardware array application as it is right out of the product. I'm trying to figure out how to position the hardware from the outside of the cabinet, or on the opposite side of where it is currently located, or to be able
Raise Bottom Drawer - FL
Hello, We have a difficult time installing the under mount slide for the bottom drawer. Is there a Global that will allow me to increase the space at the bottom for the bottom drawer? Tried changing the BOTTOM_DRAWER_SPACE_FROM_BOTTOM but that didn't
3D_HWRAssociationError
I have been creating new hardware and I am getting the hardware to showup but it is always coming in on the 3D_HWRAssociationError layer. There is no machining and irt is where I want it? Obviously there is somehthing I am doing wrong but what are the
Miter Shelf inside a cabinet
Hi all, Is it possible to put a miter shelf inside a cabinet and get the sides drilled for screws as well. Thank-you
Where to control contour for double studs on diewalls?
The interior contour for our router has 3 tight passes on a double stud and is generating an error on our router. One pass would be sufficient, where do I go to control the tool path that MV automatically generates for double studs?
Nesting with Small Line Segments
We have a new Morbidelli CNC machine that will throw out "Path Cannot Be Followed" error when we have line segments that are smaller than the tool diameter. Our Optima will cut these just fine, but the Morbidelli has issues. The tech told us to switch
Report Drawing Flatshot does not show profiles
I am wanting to send my flatshot drawings from the MV reports to our customers to confirm their order. I am embarrassed to send the current flatshot drawings. I manually add a screenshot of the cabinet from the autocad view, but this takes a long time
Global Machine Token edit
I'm looking for a method to edit a standard machine token and have it affect all parts that utilize it. The token in question is "ROUTE5[Finished End Scribe]" The Offset is hard-set to "L," which has caused us some grief. We want our added scribe to be
Request: Drill holes in tops and bottoms
Feature request, drill holes in top and bottom boards where the nailers meet, we screw into the sides and tops which helps keep units square and true but i cant see any option for it, i could add it manually but with every update i have a growing list
Material updates to product-level spec groups are changing the library spec groups
My team is currently using the Imperial Component Cabinet Library (v047.1). We have a number of times changed the Library spec groups to be our default naming conventions for materials. When we start a new project, we make copy that default spec group
Save Subassembly not working
Sometimes when I try to modify a subassembly and save it back in the library, it gets saved only in the Project, even when I check Save to Library... I end up making my modifications in the Database Explorer every time it happens. Anyone can help me figure
Panel edge bore and routing
Hi all, New user and first time poster so please be gentle 😁 The first major hurdle I have become faced with, is how to get a hardware associative machine token to work on a panel edge, not face 5 or 6. To put in context, I'm embarking on implementing
lock position
Justed added a lock by copying existing similar lock and modifying parameters. In the image below where do i changed the 7/8" distance. Currently the lock is 3/4" from the edges and needs to be 7/8". Thanks in advance
Mirroring
Hello MV team Is it possible to have a proper Mirroring function??? Ie the ability to mirror a product including all cut outs and extra machinery, we do lots of repetitive work that changes from right to left hands, it would be nice not to have to manually
Edgeband Part Size Adjustment won't work with Thickness=0
I would like to be able to use the "Part Size Adjustment" field for "Edgebanding" to oversize any edge it gets applied to by a certain amount. But currently, I have to put a thickness>0 on the edgebanding in order to do that. To avoid throwing off the
Wood Dovetail Drawers
Hi everybody, I have a probleme with the Wood Dovetail Drawers. I buy them and would love to change de depth of the drawers to be 22 inch. Do you know how to change the depth without to go on the spreedsheet.
Engineering Position Available Full Time In house
Bruewer Woodwork is a leading manufacturer of Architectural Woodwork, Casework and Retail Store Fixtures on a national basis. We are in the process of seeking an Engineer that has 5-10 years experience. The individual must have skills to communicate the
Referencing Bay Position in subassembly
What would be the best way to reference the location of a drawer subassembly when a builder is trying to determine where it goes in a drawer stack. in a previous library we appended the name of the sub front with the value of the "bay position" prompt
J-Pull tall units
Hey all i found a issue with tall door cabinets when i assign Jpull to right door it works but the left door doesnt do nothing im on library 24.0607
Drawer Pull Quantity per Front
Hi, I have 30-3/16" Wide cab with 6-drawer fronts. I only want one-handle per front, it keeps giving me two-handles. For the life of me, I can not recall where this is handled. Library version 049.1. Thanks!
Side Wall Glide Machining
After cutting out test parts on the CNC, we realized that the machining holes for the drawer glides need to move slightly forward towards the front of the cabinet. How do I change the location of the machining? And can I do to products in a pre-existing
Can a single Product Prompt Image display for a dropdown (ctrl type 5) prompt?
I know that if you save images with names that match the dropdown options, a different image can show up per selection, but can you have one image that displays for the question in general and not for each item in the list? I tried putting a jpg image
pigeon hole subassembly # of divisions & shelves greyed out
trying to insert a pigeon subassembly. works fine except # of divisions & shelves are greyed out. What am i doing wrong? (library 24.0322)
Blind Upper Cabinet from Division to Blind Hinges
Hello, When constructing Blind Uppers, we employ blind hinges to hang the doors. Previously, CL provided options to alter the door-hanging method for Blind Uppers, even though the machining and door sizes were not accurate. However, in the Foundation
Toolbox is sooooo slow and lags
I have a project I am doing, and 3D orbiting takes 10-15 seconds to just load, then I can move around, but when I release it takes another 10-15 seconds to load. Moving around in this project is miserable and makes it take 3-4 times the amount of time.
Make a New Library Product Category
I really want to add a couple new product category codes. Those category codes like "B=base" "T=tall".. I really want to have one for some other common products, so we can call on similar wiz/globals like "G!Base_Cabinet_Height" that are fundamental and
Is there a way to export a multiple projects at one time to individual Database and Zip files?
Is there a way to export a multiple projects at one time to individual Database and Zip files? Will it be added in the future? When using database management currently we can export 1 “Project” at a time sending to its own Database & ZIP file for possible use or re-import later if needed. While you can do a batch export of job, they are in 1 database and not individual. Is there a way to export a multiple projects at one time to their own individual Database & Zip files? Is it something that
Foundation Library Addition Request
It would be great if there was a way for users to help guide the evolution of the foundation library by being able to submit requests in some kind of structured way, beyond posting in general community pages. Could there be a dedicated thread? Or something
Archiving Old Projects
What is the best practice to archive old projects but still have them accessible in case of future necessities?
FEATURE REQUEST: Filtered Combo Box Dropdown
Currently, if you start typing in a combo box, it will bring you to the 1st instance of that 1st character, but it doesn't decrease the overall amount of choices in the list to ONLY those that start with that character. This would be a nice feature, and
Cannot find Gola shadow rails after install the library update
Hi all, I just updated the library to the latest Build 24.0419, which indicated that added the Gola channels for shadow rail pulls, but it seems like I cannot find it in the product prompt. Any solutions about that? Based on the update release note: https://community.microvellum.com/portal/en/kb/articles/microvellum-foundation-library-release-notes-build-24-0419
Adding Locks to the Foundation
Question, I tried to add locks to the Foundation Library following the steps in the "Adding a new hardware item to the Foundation Library". I don't have any issues adding them to the hardware library and adding the machine tokens to them. The issue that
Can "Include Routes in Border" be controlled at the part level?
We typically control this setting at the tool file level, but I noticed today that there is an option within a report for Parts.DontIncludeRoutesinNestBorder. Can this be controlled on a part-by-part basis, and if so, how? This would be very helpful to
Making a 3 panel shaker door? Is it really not possible?
I need to make a 3 panel shaker door. I have created our own door profiles we use but it is using the D! workbook LookUpTables. I am only really seeing an option for 2 panels. Seems crazy you can't door more than that.
Best Practices: Material Thickness formulas
I've been thinking about this for a while. Perhaps it is somewhat irrelevant, since parts are drawn based on the material pointers used, but not all of the materials in a spec group are used in each cabinet. Sometimes I want to refer to a particular material
Dovetail Drawer Machining
This using the component library. I would like to be able to shut off the machining for dovetail drawers as it is done off line. I could modify the subassembly and save it to the library but I would rather not go that direction just yet. I thought there
Hardware Machine Tokens - Horizontal Edge Machining
The Hardware Machine Token's only allow to add face machining to parts. Can some more tokens be added in the future to do edge machining on parts. Our new dowel machine can also do some horizontal routing and I would like to be able to put the machining
Work Order is shifting my drilling??
I have set up some drilling using dummy hardware. It works perfectly in 3D. I have checked it in 2D part editor and it works great. When I create a work order it is showing a different dimension. What would be causing this? My EB thickness and premill
How to set up machining for Blum rear hanging bracket?
Curious how to set up machining for the rear brackets that hold blum slides for face frame applications? I have looked all over but maybe I am missing something?
Custom Machining Sequence for specific partnames?
Is it possible to set the sequence of machining per parts based on their name? Similar to the "Custom Post Sequence" setting in the IPP settings but on a per-part basis? We would like to cut the border of a part before any routing operations on specific
Next Page