FEATURE REQUEST: move 2D Tokens onto their own tab (not with Prompts)
I'm sure this would be a big undertaking, but it would be helpful if the 2D Drawing Tokens (and Virtual Routes, etc) were not on the "Prompts" tab. When moving prompts around, it can be cumbersome to make sure that you are not messing up any of the stuffCOMPOUND ARC
does anyone know a quick formula to find a compound arc laid flat? for instance, i have a piece of bending ply that is wrapped on a frame and the frame is angled on one end. i'm trying to find the arc for when the piece is laid flat. i know there's aRoute Array? Is it possible
Is there a way to route multiple holes in a pattern. I know I can drill multiple holes using the bore token, but can I do the same thing using the routedhole token? Some of our products have a through hole w/ known spacing, however when drilling, we getImporting (Updated) subassembly from library?
Hi, I've edited a subassembly in a project: I've added some prompts & optional parts. I've saved it to the library, but now I'd like to use it in an existing project. But, how? I can't find a 'revert subassembly from library' button :( cheersFind and Replace Refactoring
Is there anyway to run find and replace on a selection in the workbooks? Here's what I'm trying to do: I have some machining for in wall brackets on a floating shelf. I have the product set up with prompts so that I can enter the field measurements andProduct X and Y rotation
Currently there is just a single product rotation field. which rotates the product in the Z axis, but there isn't any rotation field for rotating the product in the X and Y axis. My company has been getting increasingly frequent jobs requiring rotatedExtruded product taking to much off when a angle is used
I am using the extruded product, but when I try and use the a angle on the end it ended up taking to much off the wall.T Slot bit for Lockdowel
I have a question about the T slot tool file for Lockdowels. I am still working in the 50_7 component library for now and we are wanting to have the option to use lockdowels on our cabinets. I have set up the invisible fasteners in the construction methodtoe kick finished end prompt
can this be added to inside the cabinets like in the toe kick options tab rather than just in the subassemblies prompts.Troubleshooting SMA
Is there a way to identify a reason why a part is coming in as invalid? In the past I had found the Maximum Part Size was set too low, and that remedied a previous issue. Now I'm working with curved diewalls, and similar parts analyze correctly, whileWhere is Post Laminate Product Prompt?
We use Dado and Screw construction for most all our cabinets. This requires us to post laminate our cabinets when needing a finished end, along with some finished bottoms, tops and backs. I am unable to find the prompt that controls this setting in thePLINEs with multiple offsets in Parameter 5 lose their pocketing ability
If you offset a PLINE only once (without curly brackets around it), the option for making it a pocket will hold. However, if you offset it multiple times (which requires curly brackets around each instance), the PLINE loses the pocket option you triedHow to track what exactly has been engineered inside of cells
To keep track of which cells have been edited, we change the fill color of the cell in Workbook Designer (each engineer has a specific color). That way, others know that cell has been engineered and who did it. When possible, we also copy the old formulaCloud Based SQL Server
With COVID changing how our industry has been working from home this year I wanted to reach out and see if anyone has tried implementing Azure SQL Managed Instance for Microvellum. Eric McGillis – Regional Account Manager Microvellum Software | Streamline the Way You Work Direct: +1 (715) 781.0406 Oregon Office: +1 (541) 664.1625 Toll Free: +1 (800) 204.0913 Web: www.microvellum.com ……………………………………………………………………………………………………………………………………………………. This e-mail messageFormula help retrieving value from local product
Hi I am trying to use the local prompt for the drawer front heights (e.g Bottom_Drawer_Front_Height) within a drawer subassembly formula. I am pushing the value "Bottom" through the prompt value column to a subassembly prompt called Drawer_Position. IMore available colors in the color column
Currently you can color your prompts with the color column, but the available colors are limited to the first 9. I would like to be able to use the full AutoCAD color catalog (Either the Index Color 1 - 255, or the RGB equivalent Color Books 1-255,1-255,1-255)custom prompts
We are a custom kitchen company like most, so i would like to have some custom control global prompts. That can drive visible and or non visible prompts within all of the cabinets in the library. Which would save me time in the library designer.Refresh automatique en sortant d'un TextBox
Bonjour, un petit changement qui pourrait faire toute la différence pour nous. Nous aimerions qu'un "Refresh" soit fait automatiquement à toutes les fois qu'on sort d'un TextBox dans le formulaire "Product Prompts". De la même manière qu'un menu déroulant,FEATURE REQUEST: Minor Change to Edit Design Data Column Header Format
When "Set Standard Column Widths" is applied, the "Part Name" through the "2D Elv Token" (& Par) columns all fit visibly on my screen. However, the "Base Point", "Machine Point", "& "X,Y,Z Rotation" columns take up a lot of unnecessary real estate on2 Databases?
I have a sql server database on our network with the foundations library. I have a local database with the components library. I want to place the components library on the server as well. What is the best way to add a second library like this? Is itSMT Miters
Is there a trick to get SMT to choose the right bit when using it to machine miters? I can't seem to get it to work. https://community.microvellum.com/portal/en/kb/articles/solid-model-analyzer-solid-analyzation-tab#Miters______Section I only had oneIs there a way to disable or hide a specific type of Machine Token?
There are a few types of Machine Tokens that we'd like to disappear from the visible list, so that our users would never attempt to apply them to a part. This is typically because they either cause issues on our machines or in cutrite nesting software.Split oversized back
Hi all, is there an option in the global settings or product properties to split a back if it goes over the material size? What is the procedure for dealing with oversized backs? Thanks, Pete.Is there a way to adjust the automated lead-in that MV creates on closed/internal routes to be a straight line instead of an arc?
I know for sure it is creating this arced lead-in on 4-sided cutouts, but it might also apply to PLINES, etc. Currently, CutRite is expecting a straight route as the 1st segment, and it won't accept an arc. It therefore adds a really small segment beforecustom tab pull - foundation library
Foundation library - 23_0609 tab pulls needed a 200mm ~ 7.875in pull which wasn't there substituted in appropriate width into formula of larger pull of the machining token. =LOCALIZEVECTORLIST("1;-0.078;0|1;0.0787;0|-6.8828;0.0787;0|-6.8828;-0.078;0",UCN(1,0),1)Tall Fridge Cabinet Filler
Not sure if this is the correct area to put this, seems that the Tall Fridge cabinet scribe filler subassembly ignores a situation where there is a full end panel and only makes the filler the height of the cabinet and not the full height of the unit.disc with dado
has anyone figured out how to route a shallow dado into a circle? when i scan with SMA i get this... for some reason it wants to pocket the whole inside and when i try to add the dado to a plain disc i can't get it to lead-in without catching part ofPilot Hole Drilling on Diagonal Corner Cabinet
I have a problem with the pilot hole drilling on my Diagonal Corner Cabinets. The problem is on the Upper and Base Diagonal Corner Cabinets. The formula for the pilot holes is not moving the holes back from the corner of the top and bottom to contactLOOKUPTABLE()
Could a function be added for returning the LookupTable a cell is currently in? Similar to COLUMN() and ROW(). An example use for this function would be in the VLOOKUP formula: VLOOKUP("Text",LOOKUPTABLE(),COLUMN(),FALSE).Nesting cabinets in order of cabinet number
How do I change the nesting settings to issue cabinets in order rather than all mixed up? Thanks,Unable to Rotate Hardware
I am trying to set up machining for closet rods, and am currently having difficulty having my hardware rotate to the orientation I need. I can get it to move where I need it, but when I use the rotations it does not move. I believe it is stuck in theSheet estimates report, prior to issuing
HI there, I am a new new user with experience with other programs and I am hoping to figure out how to do a few things I could do with the last program I used. The first one is a material estimate. is there a way to get a estimated sheet count withoutBlum Aventos HK-XS
Would someone have a product with this lift system integrated? https://www.blum.com/ca/en/products/liftsystems/aventos-hk-xs/assembly/Add a Lead In Option to Straight Line Route Token
The straight line routing machine token is a very easy to use, compared to the extra time it takes to write a PLINE. The only downfall with this token is the inability to add a lead in to the route. This is an issue because we like to try and avoidCutrite Parameters From MV
I know this has worked in the past, I have seen it however i have never set it up. When your sending information from MV to Cutrite, the board information (sizes,description etc) comes in. I'm Looking for the field that contains the Cutrite OptimizationSMA issues with OEM '23
I am wondering if anyone else is running into the same issues we are ever since updating to OEM '23. We started on an earlier build but are currently on the 23.1.613.642. Similar to the "MV Extruded Product Builder" template we built "stockish" defaultExtra routing by hinge with no machining.
I am having what appears to be extra routing on cabinet ends near the hinges. It is on the face 6 face of cabinet ends. It showed up a few weeks ago but I have not asked about it earlier because the is no machining code generated for whatever it is soHow do I disable Lock Drop Front Distance
I know this variable is getting the 1.5 dim from somewhere, but I can't find it for the life of me. We don't need our fronts dropped. Please help.Display Scaling for High Resolution (4K) Laptop Monitor
I recently obtained a new laptop that has a 15.6" UHD (3840 x 2160) display. I am having trouble getting Microvellum Toolbox to display correctly with Windows 10 High-DPI scaling. The Windows 10 recommended scaling setting is 250%, which is ridiculous because everything ends up so large, there is hardly any screen real estate. I have tried setting the scaling to various settings, but the only two that seem manageable are 175% and 200%. However, at those settings, Microvellum Toolbox is a bit of aChanging Global Variables in RED
Hi, I'm trying to change the regular drawer selection from standard wood box to a Grass Zargen type. The Global is in red and I can't remember where do I have to go to be able to edit this. Thanks in advance!Next Page
Product Engineering Team Meetup
Join us for next Product Engineering Update Review
Gain an up-close view of the enhancements, additions, and modifications within the Foundation library and available expansions.
Register
MVU eLearning
Grow Your Knowledge
Follow along with RJ as he takes you on a journey to build your foundational knowledge of Toolbox.
Follow us on: