Solid Stock Report Issues
I just process a Face Frame and Shaker Door job and this is the solid stock report. What the hell is this and what can I do to figure out what is wrong. I use formula materials for the door and face frame parts and its been working fine with this format
Replace Product
I've noticed that "Replace Product" doesn't actually replace products from the library, but instead replaces product prompts. While I see this limitation could be helpful for a lot of reasons, it would also be helpful to completely replace a product,
OPTION FOR DW HOLE CUT OUT IN BASE UNITS
Have an option to make DW Service hole in the base and end of a base Cabinet
Creating report for a specific material only
Hi, We would like to run a report where only parts to a selected material are processed, is this possible? It's required for a take off to a certain material in the project. I can see in the processing center, you can load parts to the selected materials,
Face 6 axis direction single parts
When drilling face 6 single parts after sheet nesting,,,, is there a way to control which axis it flips the part, what im looking for is "longest edge on the x" type of control. hope this makes sense
Dim Sting From Wall
Where do I find an explanation for the 4 Dim Strings. I do understand that they most likely are prompts for drawing the 3D wall in Plan and Elevation. I have made a change to the wall width Dim being place off the wall 6" instead of the 26" (thanks to
Seeking Employment
Feel free to reach out if anyone is open to a remote or hybrid submittal engineer. https://www.linkedin.com/in/leepellegrin/
How to Lock a Library
I have googled the Tittle and no luck. I viewed a few Videos on creating a Library and they mention Locking the Library. Any input is appreciated and thanks in advance.
Library Designer product prompts different to products prompts
I thought I had the Library Designer figured out but I can't seem to get all my changes to work. Some changes are merged and work fine however some have only changed in the Library Designer and not in the actual Cabinets Products Prompts. Any help would
Setting up a Library
I am wondering how others handle wanting to create two different scenarios one for "Institutional/ADA" compliance and for "Residential". What is the best alternative to accomplish this? Thanks in advance for the input!!
custom global variable: =G!Dim_To_First_Drw_Slide_Hole
In the component library v050.7, the system drawer slide locations are pretty much hard-wired to the bore templates. (ie 35mm, 128mm etc for the 5mm slide mounting holes.) This leaves the drawer slides dead flush to the cabinet face, without any option
Premill allowance not being added to cut
Afternoon, The problem I'm having is that when I output parts (to Ardis, which then distibutes it to our beamsaws) all the parts show up with the .03125 premill allowance missing. For example, a 5" wide spreader would have .125" edge banding on a single
Edge band front edges with same color as exterior finish
Build 23.1.1219.641 Foundation 24.0322 How do you set the edge banding on the front edges of cabinet tops, bottoms, sides and shelves to match an exterior edge banding color? We edge band our boxes with the same color as the interior material color except
Microvellum Toolbox 2022 OEM (Cabinet Dimensions)
Hi there, How to turn on / off the dimension in cabinets just by itself (2D & 3D) The dimension in the cabinet seems to be one block or group. I’m trying to select just the dimension and it would select the cabinet box as well. Thank you, Ederwin
New Toolbox Release Available Today: Build 24.1.0416.641
We are happy to announce that Toolbox build 24.1.0416.641 is now available! This build includes resolutions for issues with Maestro Toolfile label generation, XML file conversion, and product calculation. A new saw type has been added, and new hidden
CutRite/WoodWOP Shallow Pocketing
Just throwing this question out for anyone using CutRite/WoodWOP - are your DXF layer rules set up so that CutRite/WoodWOP processes pocketing G-Code, or are you letting Microvellum process the DXF pocketing? Our current setup, which we were using with
adding bins to foundation library
hey all anyone know how to add waste bins to the foundation library we use to have lincoln sentry bin in the old library but ever since we updated to foundation its gone not sure if its Australia issue.
Product comment fields
Is it possible to populate the three product comment fields in the database from the product spreadsheet? Thx
Barcode Scanner File Path
Hey I'm wondering is there a way to have the barcode have the work order name in the file path? Currently we have the files being added to a separate folder per work order at the machine. The problem is that the machine can only scan to the H drive but
Edge Number on Label
Hey, Is anyone aware of a way to get the edge number on the part labels? We are edge boring with a single NC. file containing all edges. Unfortunately, edge 1 is usually but not always, the top of the image. This makes it challenging for the operators
Anyone know how to get jpg name to change (or display ff)
I need to update it so a filler with an applied FF panel will display on the Face Frame report. However the product name wont always contain FF and I need a way to get it to search jpg name contains " FF". Thanks, -James
Route Tool Depth
Is there a way to set the depth of a route or other operation relative to the thickness of the material in 'Draw Part in 2D' machining editor? I've had to change material thickness after a design was ready to go due to the material arriving and being
System waste bins "Euro Cargo" and similar
Hi all, In our Component Library the (Build 21.1.916.641) the choices for waste bin systems are very limited. And neither of those has machining tokens . I am curious if the Foundation Library offers a greater selection and includes machining/drilling
No Dado on my drawer box right sides
Hi Everyone, So I have a room in a project. The other rooms seem to be fine. But as I process this last room all the drawer boxes seem to be missing the drawer bottom dado's on the just the right and rear sides. Does anyone have an idea as to why this
Change bore machining diameter for woodbox drawer backs in the library or global settings.
How can I change the bore machining diameter of from woodbox drawer backs in the library settings? I have changed it manually on each product but cant find the table where the value of 6 is taken it from and doesn't match my drilling tools.
'Library Issue' - Space added to the ends of drawer kit description
Can this be updated. Everytime I upgrade to the new library the same problem comes back. The quote reports don't populate the prices due to naming mismatch. ack.
Lift up doors with regular hinges
I would like to use our regular 110deg Blum hinges for a lift up door. I see that there are many systems, but I can't find how to eliminate them (so I don't have the wrong machining), or change it to a regular full overlay hinge. Thanks!
Program Preventing Naming a Room with the same name as a Dwg within the Factory Database Directory
At some point the program started to check if there was already a Dwg within the on-disk Factory Database location by that name and prevent you from creating a room by that name. It never did this before. I figure this was obviously a change to the program
Draw Part 2d - Illegal Characters in Path
Has anyone experienced this? I've tried restarting MV however the error persists. Its only a couple parts in the job, other products/parts will allow me to draw in 2d.
Drawer Bank Cabinets
Just curious if anybody else had noticed something I just noticed this morning. Looking at the Frameless Master Cabinet List, specifically the Base 3 Drawer Split Top Drawer and the Base 4 Drawer Split Top Drawer cabinets. On the Base 3 Drawer Split Top
Change Part Properties, 2d Part ops etc. without updating sections
Currently, our 'Product Section' (Plan Section and Cross Section) drawings are deleted if we select Cancel after making changes to products/parts. Is there a way to skip the section update for insignificant changes?
update viewbase in layout
Gday is there a way to update my layouts when i have made changes to all the cabinets/walls associated with a viewbase? ie- i changed a wall length and the assciated cabinets. my layouts just show red squares where the view used to be. if i click on it
Changing Nested Quantity
Does anyone know how you can change the nested pattern quantity? I have a sheet that was optimised to run 3 times with only 2 parts on it but I know that I can manipulate it to be run just once (opening the nest drawing and moving parts). Its really just
Microvellum toolbox pallete missing
Good morning! I just opened microvellum and the toolbox palette is missing. I tried typing in "MVTB7" into the command line, still not showing up. What should I do? Thank you, Microvellum Toolbox OEM 2022 Build 23.1.407.641
New Toolbox Release Available Today: Build 24.1.0409.641
We are happy to announce that Toolbox build 24.1.0409.641 is now available! This build includes resolutions for issues with labeling, barcode generation, border routes on parts created in the Solid Model Analyzer, 3D Drawings from the Product Viewer,
Toe Kick & Countertop Options - more local control
It would be great to have these subassembly prompts available at the local level. Will the dev team add this in a future Foundation update please?
export
Hey all is their a way to export all microvellum product names even better a export categories and product names many thanks
fixed shelfs
is it possible to add led strip lights to fixed shelfs as we have a under panel with option many projects im doing lately all want leds
Number of Parts Processing vs Time
30 (identically shaped) parts. Diewall with conical shaped interior. I go to work order creation, hit process and wait... Processing: 1 Part = a couple seconds 2 Parts = a few more seconds 4 Parts = quite a few seconds 7 Parts = maybe a minute? If I process
3D Hardware Folder
I have been trying to find where the 3D images for the hardware is in microvellum. I cannot seem to find it anywhere. Would someone be able to point me in the right direction
Next Page